מטעין נמוך

Fliegl VTS S Parab/Feder

Further information
Chassis low loader trailer
Welded steel construction
Turntable with powerful ball bearing slewing ring
Folding rear support
2 wheel chocks with holder
Aluminum side bumpers
Rear spray flaps across the entire width
Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle
Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope
1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery)
1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm
Lsdpfxsi Ri A So Ad Iohp
Extensions extendable to 3,000 mm
Wooden planks 70 mm for widening to 3000 mm
Storage compartment for wooden planks under the loading area
Low loader lashing eyes (40 lashing options)
1 pair of lashing eyes on offset per 5 tons
9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame
2 x front on offset
7 x in the drop deck
6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment)
3 additional pairs of hinged lashing eyes, 10 tons each
1 x inside next to the main frame at the start of the low bed
1 x on offset (protrudes)
1 x embedded in the floor behind the last axle
Towing equipment Trailer turntable
Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN
Axles + suspension
Drum brake axles
Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation)
Wheels and tires
235 / 75 R 17,5
at the manufacturer's choice
Twin steel rims, factory silver
Brake system
2-line compressed air brake system
Spring-applied parking brake
2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle,
ABS and ALB, with ABS plug at the front, with connecting cable
Electrical system
24 volt, multi-chamber lights, amber LED lighting at the side
2 white position lights at the front
2 white/red lane departure lights at the rear
2 x 7-pin interchangeable plugs at the front, with connecting cable,
1 LED rotating beacon with holder, switched via parking light (removable light)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
Offset at the front with steel/ checker plate flooring
Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area
Rear slope with 70 mm softwood flooring
Drive-on ramps
Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways
covered with wood
with spring lift support
Country of registration / plates
Country of registration: Germany
24/7 service hotline
Prepared for two-line license plate holder
Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear
Warning sign according to ECE - 70
Paintwork
Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through
Drawbar Galvanized or black, at the manufacturer's discretion
Drive-on ramps Hot-dip galvanized
Attention! These are archive pictures!

המודעה תורגמה אוטומטית. ייתכנו שגיאות בתרגום.