תְּצוּרָה חֲצוּיָה עִם מַשָּׂא נֶחְלָף

Abrollcontainer Container 6,5 m Kran Fassi F150

Brand new roll-off container with FASSI loading crane

Roll-off container in a platform design with aluminum sideboards
and a permanently mounted Fassi loading crane

ELLERMANN roll-off container according to DIN 30722-1
with aluminum sideboards and crane platform
Platform tipper body type K 33 s
Internal dimensions: approx. 6.5/5.3 x 2.42 x 1.0 meters, all dimensions are approximate
Useful volume: approx. 13 m³
Paint finish: in RAL color according to customer's request

? Mounting brackets for hook lift systems according to DIN 30722-1 (15,000 kg)
with rear outside rollers and subframe made of INP 180
Outside rollers are greaseable and replaceable
Mounting bracket Ø 50 mm, hook height 1,570 mm
Transition from the subframe to the end wall support reinforced with 10 mm gusset plates
? Crane platform 20 mm thick at the end, length approx. 1,200 mm
Reinforcement on the end wall support and subframe inside
Additional stiffening on the end support
? End wall inner height approx. 1,000 mm
? Floor made of 5 mm St 37.2 (S235JR)
? Floor spar spacing 500 mm
Spar profile U 80 x 50 mm
? Outer profile as a hole strip (a hole Ø 40 mm every 200 mm),
Loadable with 500 kg / hole, max 5 tons per side, operable from the inside
? Aluminum sideboards, approx. 1.0 meter high, foldable and removable,
1 x divided in the middle by a removable center post
? Aluminum rear flap, foldable and removable (cannot be driven over) with removable corner posts
? All-around tarpaulin and net hooks
? Container double primed inside and out and double painted in a single color inside and out
? Aluminum sideboards unpainted
? UVV stickers with safety instructions
? Container tested and approved according to DGUV rule 214-017 (formerly BGR 186)
? Container test book (digitized) for documentation of the
required annual recurring inspection according to UVV

FASSI loading crane F150A.2 e-dynamic

Design according to CE directive (EN 12999)
The equipment manufacturer must carry out the inspection
once the loading crane has been mounted in its final position
and is ready for operation.
Dcodpszq Iu Iofx Airjk
Base unit: F150A.2 e-dynamic
Slewing range 416°
All hydraulic cylinders are double-acting
Piston rods are hard chrome-plated
Double lever system with PROLINK (overextension of the knuckle arm up to 15°)
Electronic overload protection device with FX500
6 functions RCH or RCS radio remote control (linear levers) with
Display and XP system
Emergency stop, as well as optical alarm (90% and 100%)
Including digitally adjustable slewing limit
FASSI stability control FSC including LMB II
Pressure relief and load holding valves, high-pressure filter
Danfoss S800 control block with 4 control valves, operable from one side
Separate hydraulic tank (90 l) with filter, mounted on the crane base
Extendable on both sides, support width 4.60 m, hydraulic support - CE, including M.O.L.
Standard color RAL 3020 traffic red - all cylinders painted black
Load hook and attachment bridges (short / 500 mm)
Driving position: folded transversely to the direction of travel
Dead point above the support beam
Caution: Note the on-board voltage / 12 V or 24 V, standard 24 V

F150A.2.23 e-dynamic » Base unit
IE742 connection box
Support spread to support width 5.4 m
Move dead point
1 LED work light on the knuckle arm » mounted
LED for 2 outriggers, not mounted » (crane)
Control system for 2 additional functions with » 2 hose guides / eactive
Slewing valve, only for cranes with rack and pinion
Quick-release valve for the extensions
E

המודעה תורגמה אוטומטית. ייתכנו שגיאות בתרגום.