נגרר סמי נמוך

Fliegl SDS 510 mit Tiefbett

Custom-made transport solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements.

Chassis: Low-loader semi-trailer
Steel welded construction, kingpin plate with 2 replaceable kingpins
24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without stroke compensation
Folding rear support
2x chock blocks with holder
Aluminum side impact protection
Quarter panel fenders in front of and behind the axle assembly
with splash flaps behind each axle
1x storage box, w=2,350 mm x l=730 mm x h=640 mm, mounted crosswise at the front on the floor of the gooseneck, with 2 storage trays
Extendable widening elements up to 3,000 mm (not in rear slope)(However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm)
Storage compartment for wooden planks on the gooseneck, at the front, crosswise
Wooden planks 70 mm for widening to 3,000 mm
Excavator arm recess starting above the rear axles to the rear, approx. 500 mm wide and approx. 230 mm deep
Tie-down points: Low-loader
3 pairs of tie-down points, each 10 tons, at the front of the gooseneck, 8 pairs of tie-down points, each 10 tons, in the low bed, 3 pairs of tie-down rails in the wheel track area of the low bed, 3 pairs of tie-down points, each 10 tons, in the axle/rear area
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-measured, reducing tire wear and fuel consumption
with steering axle
Air suspension
Wheels and tires
235 / 75 R 17.5
as chosen by the manufacturer
Steel rims in twin arrangement, factory silver
Braking system
2-line pneumatic braking system, color-coded lines for easy servicing
Spring brake parking brake
EBS, Electronic Braking System with EBS socket at the front, without connecting cable
Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS!
2 fail-safe coupling heads at the front, without connecting line
with lift & lower valve, hold function in the lowered position + auto-reset function
Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scale)
Vehicle - Driving stability system
Trailer Info Center, for displaying vehicle data such as axle loads (no calibrated scale), mileage and diagnostic/system messages
Electrical system
24 volts, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front in LED
2 white/red marker lights at the rear
Hodpfxji Ri Hgo Aldjnp
2 x 7-pole fail-safe sockets at the front
1x additional LED work light at the rear
1x LED rotating beacon with holder, switched via parking lights
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
Gooseneck with steel/diamond plate covering
in the wheel track area with 70 mm softwood floor, in the wheel arch area steel/diamond plate covering, low bed on the left and right in the wheel track area can be hydraulically raised for entry, via truck auxiliary drive
Rear slope with 70 mm softwood floor
Low bed length approx. 6,300 mm
Side walls
25 mm aluminum hollow profile, 400 mm high, can be plugged into the front and side on the gooseneck
Ramps
Steel ramps 2,800 mm long, 750 mm wide

Custom-made transport solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown i

המודעה תורגמה אוטומטית. ייתכנו שגיאות בתרגום.