מכונת גריסה גלילית - אוניברסליתKELLENBERGER
Kel-Varia UR225-1500 FANUC
מכונת גריסה גלילית - אוניברסלית
KELLENBERGER
Kel-Varia UR225-1500 FANUC
שנת ייצור
2002
מצב
משומש
מיקום
Kirchheim unter Teck 

נתונים בסיסיים
מחיר ומיקום
- מיקום:
- 73230 Kirchheim

התקשר
פרטי ההצעה
- מזהה מודעה:
- A17404443
- מספר התייחסות:
- 1056-M24Vari
- עדכון:
- עודכן לאחרונה בתאריך 10.11.2026
תיאור
grinding diameter 450 mm
grinding length 1500 mm
centre height 225 mm
Control FAGOR
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
Hnedpfxeuxfu Nj Afhjw
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
grinding length 1500 mm
centre height 225 mm
Control FAGOR
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
Hnedpfxeuxfu Nj Afhjw
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
ספק
הערה: הירשם בחינם או התחבר, כדי לקבל גישה לכל המידע.
נרשם מאז: 2002
47 מודעות אונליין
שלח בקשה
טלפון & פקס
+49 7021 ... מודעות
ייתכן שגם מודעות אלה יעניינו אותך.
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Dortmund
3,193 km
מחזיקי כלים מונעים ישרים
NACKE + WTOVDI 50
NACKE + WTOVDI 50
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
גרמניה
3,006 km
מכונת טחינת משטח CNC
JungJE600
JungJE600
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Offenbach an der Queich
3,009 km
מכונת חיתוך ומרוכז
UMA - SZMSZM 100/1000
UMA - SZMSZM 100/1000
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Mönchengladbach
3,230 km
מכונת מדידה מתואמת
MitutoyoCrysta Apex C776
MitutoyoCrysta Apex C776
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Ybbs an der Donau
2,535 km
ספקטרומטר FTIR - NICOLET IS20
ThermoFisher ScientificNICOLET IS20
ThermoFisher ScientificNICOLET IS20
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Contamine-sur-Arve
2,970 km
מחרטה אוטומטית רב-צירי CNC
INDEXMS32C
INDEXMS32C
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Hövelhof
3,146 km
מקדחה טוויסט וגריסה countersink
Rohde&Doerrenberg (May)SS 40U
Rohde&Doerrenberg (May)SS 40U
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Brügg
2,954 km
מכונת גריסה מעגלית CNC
KELLENBERGERKEL-VARIA R175 x 1500
KELLENBERGERKEL-VARIA R175 x 1500
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
גרמניה
3,050 km
Schaudt Mikrosa SASL 125
Schaudt MikrosaSASL 125
Schaudt MikrosaSASL 125
מוצלח
ההודעה שלך נשלחה.
מודעה קטנה
Lontzen
3,229 km
מכונת השחזה גלילית
TosBUB E 50/2000
TosBUB E 50/2000
המודעה שלך נמחקה בהצלחה
אירעה שגיאה


















































































